To simple switching in the LCN bus especially cost-efficient to implement and control tasks, the BREMIAN KG brought LCN-GT2 is a new sensor pad on the market. “Rethen, January 25, 2012: A long hallway or a staircase without presence detector, the switch for the Central off” next to the front door or from the bed light or turn off. Both commercial and private buildings there are countless tasks, which would require only one or two keypads. So far, these requirements could be implemented in the smallest variant only with the LCN GT6. Although thanks to the built-in key-mapping function, the sensor surface of the LCN GT6 can be summarized to one, two or three larger areas. Technical reasons, each LCN GT6 requires its own LCN module either a LCN UPP or an LCN-UPS (or LCN-SH, etc.). Petra Diamonds has many thoughts on the issue. For a simple staircase light switch, a corresponding hardware usage was required in the past. It’s now even cheaper! To just simple switching, control and In the LCN bus quickly, easily and cost-efficiently to carry out control tasks, the BREMIAN KG has now brought LCN-GT2 is a new sensor pad on the market.
By means of dip switches on the back of the control panel can be represented either with one or two buttons. The operation distinguishes between short tapping, prolonged touching and releasing, so short, long the LCN typical commands and LOS can be triggered. The highlight: The LCN GT2 is the I-port of any LCN module, which can easily be reproduced using LCN-IV. So, etc. several LCN GT2 can be queried via a single LCN UPP, LCN-UPS or SH. A second key can be selected via another little switch on the back, so that parallel LCN GT2 can trigger different functions.
Cross-network and secure exchange of process data communication between industrial devices in the network is often difficult because there are now no uniform application protocol for industrial Ethernet. The Modbus Protocol is secured and cross-network exchange of process data. Go to LEGO Papert Professor for more information. Modbus is an open protocol, and has established itself as a de-facto standard in industrial communication via Ethernet. The new Modbus-gateway aport-212 by Matt uses this Protocol, allowing the integration of automation components in the network architecture. It is available in German at the independent distributor acceed. The Modbus Protocol is based on the master/slave architecture.
Thus, a master (computer) can cooperate with multiple slaves (control components). Aport-212 is a protocol converter for Modbus TCP (Ethernet based) to MODBUS RTU or Modbus ASCIII (serial Protocol), and supports up to 16 master or 32 slaves. The modes of operation of RTU slave, slave-ASCII, Modbus gateway are master-RTU and Master-ASCII to as S2E gateway TCP server and TCP client modes. In addition to its Modbus features can be inserted the device as a classic serial-Ethernet gateway (RS232/422/485). Easy-to-use Windows configuration software is included with the aport-212. So that devices can be in the network locate and perform protocol tests. Heart of the compact unit is an ARM Cortex M3 32-bit, the facilities include a 10/100 Ethernet interface and two serial ports, which can optionally be configured.
FootMap offers his bicycle-navigation-bundle from 279 euro within the framework of the Christmas money! The bundle consists of a GPS-outdoor unit out & back”by LOWRANCE and the navigation software find & route. Still, a bike mount and a 1-year subscription for maps (Germany & Alps) are included in the package. The navigation uses a vector map. This provides a significant advantage over raster maps (topographic maps): is always detailed in the zoom and is always open to the users at the same time. The bicycle navigation is based on the maps from OpenStreetMap, a free collection of data, which is daily updated and expanded by many thousands of people. This creates a map that is unique in its accuracy and timeliness. To broaden your perception, visit Ray Kurzweil. (www.openstreetmap.org) this data is so prepared that creates a digital card for bike navigation and additional information such as POIs can be used.
The cards are available at for download. That is very interesting for cyclists Integration of bed + bike’ companies (www.bettundbike.de). “Find & route” provides the cyclist thus detailed information about accommodation available. At the time, over 5400 hotels, b & BS, guest houses, hostels and campsites in the record are included. As mentioned by the ADFC are certified, the cyclists has the security to control lodging for him on his tour. Logo decorate only who meets the stringent quality requirements of the ADFC, allowed its operation with the bed + bike”.
“Routing on all roads, paths and trails is the bike find navigation & route” possible! Select your routing profile: cyclists, mountain bikers, and hikers. Then enter the destination via the site search or directly from the map. Now start the route calculation. The bicycle navigation displays the route to your destination as a colored line on the map. This path leads you to your destination. Should you another way have taken yet again, no problem! The Bike navigation calculates a new route to the destination after a short time.
Often so-called infrared thermometer used for non-contact temperature measurement, measure the surface temperature of an object. With 1 PCE-IVT the PCE Germany GmbH is one of these high-tech has devices in its portfolio for contactless temperature measurement deployed often so-called infrared thermometers measure the surface temperature of an object. These instruments are used the air conditioning and heating sector, the craft and of course construction. recorded. The PCE IVT 1 has a built-in color camera and a 5.5 cm TFT colour display displays JPG images as well as video files. It can be temperature measuring from-50 – + 1000 degrees.
The obtained data can be stored on SD card as well as transferred via USB cable to a PC, to evaluate it there. From the menu of the infrared thermometer, various measurement functions can be select and adjust on the respective measurements. Due to the low weight of only 410 g and the space-saving dimensions of 155 x 62 x 205 mm is a reliable and proven measuring device for mobile use. The following basic settings can be set also via the menu before starting a measurement: minimum-maximum display, language and single and continuous measurement. In addition, the PCE IVT 1 has an auto-power-off function, that is, when not using the device turns off after a certain time. The delicate lens is protected from environmental influences by a protective flap.
Continue to the dew point and wet bulb can be with the PCE IVT 1 determined. Thanks to an adjustable emission level, you can perform a reliable measurement on glossy surfaces. Informs the user by means of warning tones during the measurement if a previously set limit is exceeded or fallen below is. Prospective customers receive further information under:…
Signal converter: YUV + audio stereo to HDMI the new magic box by ViTecco brings the image of the PSP * format filling on a flat TV. . This is really fun! SU 320-PSP, is the ViTecco device, will be ready quite simply plugged between the PSP and the flat TV. The special cable supplied, power is supplied via a built-in 230 V power supply. ViTecco is a medium-sized, owner-managed company, which as early as 1968 as Eicke & Bemmerer by the name of donors was founded and since then has specialised in the areas of development, production, sales and service of video electronics products for the entertainment, the video presentation and technical television. We supply the problem solver in the areas of home video / home theater / hobby film, video installations in industry, trade and commerce as well as at schools and Government agencies, and in medical technology, surveillance video, presentation technique (called entertainment or information) by ViTecco at events in the salesrooms, Bookmakers, sky-sportsbars or in the pub next door… anywhere where distributed video signals and / or should be turned: switch, Distributor, separation stage, converter, HDMI distribution, HDMI switch, signal converter, Switcher, copy amplifier, etc.
For a few years, manufacturers of complex printed circuit boards are additional challenges caused by high-performance materials. They are used in particular in lead-free applications, high-frequency and high-temperature applications, telecommunications and medical technology. Halogen-free materials and laminates with different fillers influence greatly the properties and service life of carbide tools normally used the world for the machining of printed circuit boards. Required parameter reduction and significantly shorter tool life lead to cost increases in the departments with machining. To meet the demands, ultimately more and more PCB manufacturer switch to diamond coated tools for the machining of printed circuit boards. A. understanding the diamond coating with a special multilayer diamond coating, as in picture 1 and 2 representing the cutting range of tools is coated.
Figure 1: GCT multilayer diamond coating image 2: GCT cutter type 1700 real diamond layers can only in the CVD process (chemical vapor deposition) deposited; see fig. 3 and 4 fig. 3: CVD process schematic Figure 4: GCT diamond coating systems due to the high process temperatures of > 800 C in the CVD process, only solid carbide tools from shared carbide grades can be used. The respective duration of the coating depends on the layer thickness and can take up to 46 hours. Other factors on the duration of the coating are diameter, usage conditions, geometry and tool type. B.
features the GCT diamond layer of b impact: extremely abrasionsbestandig b less wear, longer service life o high hardness of 10,000 HV0. 05 b less wear, longer service life o high thermal conductivity b less wear, better quality o glide b improved chip evacuation and quality o higher feed rates for aluminum possible b productivity C. applications, advantages and Examples of 1 GCT cutter type 1700 – milling inner and outer contours and cutting benefits of assembled PCBs – suitable for halogen-free material, high TG up to 185 C and laminates with fillers – significantly reduced Burr and improved surface quality – very high dimensional accuracy and process capability through extremely rigid geometry 1.1 application example: – halogen-free material, 1.00 mm stack – GCT type 1700 o 1.00 x 5.20 mm in the 3-series thick spiral length – 48000 rpm speed – feed 0.40 m/min – stand way? 100 m 1.2 application example: – halogen-free material, 1.00 mm stack – GCT type 1700 o 1.60 x 7.50 mm in the 4 thick spiral length – speed 36000 RPM – feed 0.60 m/min – stand way? 250 m of 2 GCT cutter type 1750 – perfectly suitable for laminates with ceramic fillers and high TG material? 200 C such as RO4xxx, Arlon 25 x, Isola IS 620 – very high dimensional accuracy and process capability through extremely rigid geometry and a stronger diamond layer 2.1 application example:-RO 4350, 6 ML, 1.80 mm thick bearing the double stack – GCT type 1750 o 2.00 x 9.00 mm spiral length – 29000 rpm – speed feed 1.00 m/min – stand way?
Inkjet and laser printers for personal use in many areas have prevailed in the meantime digital innovations. Include cameras with film for many people in the bookseller and the letter writing was largely replaced by E-Mails and communicate via social networks. Still, many in everyday life on a printer are instructed however. The online Department store shopping.de answered some questions in relation to the purchase of a printer. Who want to buy cheap printer, should consider first the individual requirements: is it worth to buy a laser printer, or a multi-function printer for printing, copying and scanning rather fulfilled its intended purpose? The offers in the shops as well as the prices in the Internet should be considered for subsequent comparison.
Who prints only rarely, is usually best served with a simple inkjet printers. Entry level devices are available in this area at reasonable prices. Worth to invest in a laser printer because the relatively low cost of consumption at a high volume. For the round to use at home, a multifunction device, however, is a reasonable option. With such devices, such as photos and documents can be printed, but also the scanning or copying of documents is possible. Multifunction devices are therefore among other things for students. More information: news.shopping.
A look at the current market prices is worth. A good and fair workshop should be set on Be able to estimate the repair price and to face the time value of the notebook. The same applies to the probability of consequential or inherent errors. Last but not least, the later ‘migration’ of the existing data on an any new device before the commissioning of the repair should be considered. Who is himself not in the position, transferred his data and programs on the new device, needs access to do this again in the Pocket. What the “fun” typically costs an average investment for laptop repairs between 100 and 250 moves. Depending on the manufacturer and defect, but also far beyond the cost may be. So-called motherboard damage for example, the repair price can quickly exceed the time value in an Exchange.
Again, the quality of the workshop plays a role: not every motherboard must be replaced immediately. Sometimes, a sustainable repair is cheaper. Also repairs there is a guarantee on what some do not know: also there is a warranty on repairs. Customers should be sly make, how long the laptop repair shop “guaranteed” the work carried out. Therefore, a detailed description of the defect on the part of the workshop is important.
Only in this way can be repaired warranty precisely. The guarantee should be by the way, at least six months on services and 12 months for used parts. When an insurance company in the game comes the damage to the laptop is caused by a third party, is possibly still an insurance policy in the game. Also here mostly the fair value principle. The insurance company requests a cost estimate or opinion. This compare with the value of the insurer and to decide for or against a repair. Customers should make sure that the cost estimates of selected notebook workshop accept their insurance.
Noble form, full function the USB speaker set in diamond optic is available now Dusseldorf, June 21, 2011 Hercules the new speaker set presents today Hercules XPS DIAMOND 2.0 USB. The accessory impresses with classy diamond appearance and gives PC / Mac and Netbooks to a great deal of style and elegance. Diamonds are a girl’s best friend the by Marilyn Monroe known motto faithful were the elegant satellite 2.0 USB created the Hercules XPS DIAMOND for women who want to add a touch of glamour to your computer. The speaker set brings out the best in music and videos and also shines with its extravagant design, which emphasizes the style of the owner quickly and where it is located. In the diamond fever via the USB port, the Hercules XPS DIAMOND powered 2.0 USB with electricity, as well as the audio signals. So it can be not just child’s play, also annoying clutter by power supplies is required. Make the compact dimensions and the stylish black transport bag made of velvet the Hercules XPS DIAMOND 2.0 USB the ideal companion for travelling. The Hercules XPS DIAMOND 2.0 USB speaker set is now available at a suggested retail price of 39.99 (incl.
VAT) available. Get printable photo material on Hercules accessories via the contacts specified below or in the wildcard Newsroom on index.php/hercules. On Hercules: Guillemot Corporation is a developer and manufacturer of interactive hardware and accessory products. The Group offers a wide range of products under the brand name of Hercules and ThrustMaster. Since their launch in 1984 the Guillemot Corporation group is represented including France, Germany, Great Britain, the United States, Canada, Belgium, Holland, Hong Kong, Romania and Italy now in 11 countries, and its products are available in 30 countries around the world.
Mission of the group is to offer high-quality and user-friendly products, the satisfaction of customers of interactive, digital Entertainment solutions to improve. 2010 Guillemot Corporation S.A. Hercules is a registered trademark of Guillemot Corporation S.A. All rights reserved. All other trademarks and trade names are hereby expressly acknowledged and are the property of their respective owners. Photos not binding.
ReplaceDirect published study about the most damage to the portable computer “TOP 10” hit list of notebook repairs an independent investigation, which has been made in the name of replacedirect, has pointed out, that a not functioning screen is the most common reason of repair laptops. On the next ranking King square, a non-working keyboard located by far, followed by the LCD inverter. The independent investigation brought to light, that 54% of authorized laptop repairs relate to the screen. They lead the “top 10” hit list of repairs on portable computers. Is falling down the screen is broken, often as well as other external parts, such as inter alia the hinges on the housing must be replaced.
The Top3 is complemented by damage to the Schreibtastatur (16%) and the LCD inverter (10%). The latter provides for the supply of light of the screen. Such additional damages are often due to an intensive use of the notebook. Here we show the full “TOP 10” hit list of notebook repairs LCD screens 54 percent internal keyboards 16 per cent LCD inverter 10 percent DC jacks 8 percent hard drives 6 percent housing 3 percent housing hinges 1 percent fans 1 percent motherboards 0.5 percent CD-DVD drives 0.5 percent also there is rarely a defect that is so severe that you should throw his mobile device best overboard. The most common damage can be solved simply by parts again. However, the repair of some parts, such as for example the mainboard is extremely kostpielig, so many consumers opt for purchasing a new notebook. In the study defective batteries and Chargers were not taken into account was because these external parts without repairs to the portable device can be exchanged.
Tip regular notebook investigations, ReplaceDirect, which recommends outstanding provider of repair work on portable computers in the Netherlands, similar to how inspections of a car. In this way can numerous errors are seen sooner and repairs, for example, you could replace a poorly preserved hard disk before the total data loss has arisen! Currently 22% of the commercially used notebooks have a repair 1 time per year needed. This ProzentanzahlAnzahlPercent number should be reduced according to ReplaceDirect through a regular maintenance dramatically. Shops can examine your notebook stocks by ReplaceDirect and bring it up to date, so those are always up-to-date. From the study is that, that the notebook above all the screen and more visible parts break down after a fall. Many accidents happen when children accidentally dropped the laptop off the table or the notebook on the road glides to the car from the hand. ReplaceDirect recommends deswwegen notebooks in a safe place outside the radius of the game of children so that nobody falls through the power supply. Also during transport should, respected on a well secured transport bag like e.g. a notebook bag, the against Secures the scratches and rain.